V.10 Interface on the TeKaDe FS-220(Z)

For service and support with i-Telex, its components and teleprinters in general

Topic author
ash
Rank 1
Rank 1
Beiträge: 9
Registriert: Sa 13. Jun 2020, 06:28
Wohnort: Wakefield, United Kingdom
Hauptanschluß:
Kontaktdaten:

V.10 Interface on the TeKaDe FS-220(Z)

#1

Beitrag: # 18876Beitrag ash »

Hello,

I have recently bought a TeKaDe FS-220(Z) with the impression that it would support V.10 out-of-the-box, as indicated on page 43 (31) of the manual [1]. However, when it arrived, it only seems to have the arcane ADo8 interface [2], for which I can't find much information; it seems to be something from the pre-T.A.E. era [3, 4]. Nevertheless, I would still like to use V.10 to connect the TTY to my computer (Gentoo Linux), by converting the well-documented signal (EIA-530) [5] to an RS-232 interface [6, 7], which can then be converted to U.S.B. with the CH340 (supports five-bit character encoding) chipset [8, 9].

Does anyone know how to use the V.10 interface with the FS-220 ? I was looking at [10]---the same vendor from whom I purchased the TTY---however I am very unsure at this point.

Thanks,
Ashley.

[1] https://cryptomuseum.com/telex/tekade/f ... /fs200.pdf
[2] https://de.wikipedia.org/wiki/Anschluss ... _und_ADo_8
[3] https://www.cryptomuseum.com/telex/ (ADo 8 sub-heading)
[4] https://www.toytowngermany.com/forum/to ... e-sockets/
[5] https://pinouts.ru/SerialPorts/eia530_pinout.shtml
[6] https://pinouts.ru/SerialPorts/RS232_pinout.shtml
[7] https://raw.githubusercontent.com/wiki/ ... erEcho.png
[8] https://github.com/fablab-wue/piTelex/wiki/HW_V10
[9] https://www.ebay.co.uk/itm/112953379508
[10] https://bw-schmitti.de/produkt/ergaenzu ... nen-fs200/
Benutzeravatar

DF3OE
Founder
Founder
Beiträge: 3067
Registriert: Di 7. Jun 2016, 09:45
Wohnort: Edemissen - Blumenhagen
Hauptanschluß: 925302 treu d
Kontaktdaten:

Re: V.10 Interface on the TeKaDe FS-220(Z)

#2

Beitrag: # 18877Beitrag DF3OE »

Almost likely the connector with ADo8 is a 40ma line current interface.
mfg
henning +++

925302 treu d - T1000Z (Hauptanschluss)
55571 fvler a - T100S
210911za hmb d - T150 (Werkstatt)
218308 test d - T1000S/LS (Werkstatt)
925333 =treu d (Minitelex Sanyo SF100) defekt
Fax G2/G3: 05176-9754481 (Sanyo SF100 Thermofax) defekt

deBart
Rank 3
Rank 3
Beiträge: 119
Registriert: Mi 13. Nov 2019, 11:26
Hauptanschluß: 35822 STIKO NL

Re: V.10 Interface on the TeKaDe FS-220(Z)

#3

Beitrag: # 18878Beitrag deBart »

If I understand correctly, there are two physically different interfaces available of which you can plug in *one* in the FS220. Could it be that you just have the 'wrong' one in there?
BartW. +++

35822 STIKO NL - FS220 + Fsg T56
42223 CMVZW NL - T100 mit Fsg 100 TL
T1000Z - Lauft (noch lange) nicht :coffee:

Topic author
ash
Rank 1
Rank 1
Beiträge: 9
Registriert: Sa 13. Jun 2020, 06:28
Wohnort: Wakefield, United Kingdom
Hauptanschluß:
Kontaktdaten:

Re: V.10 Interface on the TeKaDe FS-220(Z)

#4

Beitrag: # 18879Beitrag ash »

deBart hat geschrieben: Sa 13. Jun 2020, 12:29 If I understand correctly, there are two physically different interfaces available of which you can plug in *one* in the FS220. Could it be that you just have the 'wrong' one in there?
In that case, will I need to remove the backplate and replace the ADo 8 card with [1] ? I still have yet to work out how to remove the backplate: I removed all the screws and it still won't budge a centimetre. I can't work out whether it's because it is rather old, and has thus "seized up", or I am doing something wrong.

[1] https://bw-schmitti.de/produkt/ergaenzu ... nen-fs200/

deBart
Rank 3
Rank 3
Beiträge: 119
Registriert: Mi 13. Nov 2019, 11:26
Hauptanschluß: 35822 STIKO NL

Re: V.10 Interface on the TeKaDe FS-220(Z)

#5

Beitrag: # 18880Beitrag deBart »

ash hat geschrieben: Sa 13. Jun 2020, 13:21 In that case, will I need to remove the backplate and replace the ADo 8 card with [1] ?
I suppose so
I still have yet to work out how to remove the backplate: I removed all the screws and it still won't budge a centimetre. I can't work out whether it's because it is rather old, and has thus "seized up", or I am doing something wrong.
Can't recall exactly, but did you start by taking the top off?
BartW. +++

35822 STIKO NL - FS220 + Fsg T56
42223 CMVZW NL - T100 mit Fsg 100 TL
T1000Z - Lauft (noch lange) nicht :coffee:

Topic author
ash
Rank 1
Rank 1
Beiträge: 9
Registriert: Sa 13. Jun 2020, 06:28
Wohnort: Wakefield, United Kingdom
Hauptanschluß:
Kontaktdaten:

Re: V.10 Interface on the TeKaDe FS-220(Z)

#6

Beitrag: # 18884Beitrag ash »

deBart hat geschrieben: Sa 13. Jun 2020, 14:50 Can't recall exactly, but did you start by taking the top off?
Damn - I was trying to remove the backplate, not the top. I can't imagine why there are external screws on the backplate, when it obviously needs to be unscrewed from the inside. The top comes off easily, and it seems like that V.10 card from BW-Schmitti will fit it perfectly. Cheers for the help, even if it did just involve removing four screws. Now the challenge is getting the top back on. ;-)

Thanks again,
Ashley.
Benutzeravatar

DF3OE
Founder
Founder
Beiträge: 3067
Registriert: Di 7. Jun 2016, 09:45
Wohnort: Edemissen - Blumenhagen
Hauptanschluß: 925302 treu d
Kontaktdaten:

Re: V.10 Interface on the TeKaDe FS-220(Z)

#7

Beitrag: # 18885Beitrag DF3OE »

The "V.10 card" that BW-Schmiti sells in his shop is actually a 40ma linecurrent card. Since this guy is an ordinary scrap dealer he
does not know what he is selling fortunately. ;)
Generally the V.10 interface is fitted with a DB-25 connector. Although there might be a few excecptions, but VERY few
that also use ADo8.
mfg
henning +++

925302 treu d - T1000Z (Hauptanschluss)
55571 fvler a - T100S
210911za hmb d - T150 (Werkstatt)
218308 test d - T1000S/LS (Werkstatt)
925333 =treu d (Minitelex Sanyo SF100) defekt
Fax G2/G3: 05176-9754481 (Sanyo SF100 Thermofax) defekt

deBart
Rank 3
Rank 3
Beiträge: 119
Registriert: Mi 13. Nov 2019, 11:26
Hauptanschluß: 35822 STIKO NL

Re: V.10 Interface on the TeKaDe FS-220(Z)

#8

Beitrag: # 18886Beitrag deBart »

DF3OE hat geschrieben: Sa 13. Jun 2020, 16:47 Generally the V.10 interface is fitted with a DB-25 connector.
Isn't that exactly what he BW-Schmitti selling? https://bw-schmitti.de/produkt/ergaenzu ... nen-fs200/
BartW. +++

35822 STIKO NL - FS220 + Fsg T56
42223 CMVZW NL - T100 mit Fsg 100 TL
T1000Z - Lauft (noch lange) nicht :coffee:
Benutzeravatar

DF3OE
Founder
Founder
Beiträge: 3067
Registriert: Di 7. Jun 2016, 09:45
Wohnort: Edemissen - Blumenhagen
Hauptanschluß: 925302 treu d
Kontaktdaten:

Re: V.10 Interface on the TeKaDe FS-220(Z)

#9

Beitrag: # 18888Beitrag DF3OE »

Yes, that's a V.10 module on the photo, but others of the group also already received line current modules when
they ordered a V.10 card... ;)
mfg
henning +++

925302 treu d - T1000Z (Hauptanschluss)
55571 fvler a - T100S
210911za hmb d - T150 (Werkstatt)
218308 test d - T1000S/LS (Werkstatt)
925333 =treu d (Minitelex Sanyo SF100) defekt
Fax G2/G3: 05176-9754481 (Sanyo SF100 Thermofax) defekt

deBart
Rank 3
Rank 3
Beiträge: 119
Registriert: Mi 13. Nov 2019, 11:26
Hauptanschluß: 35822 STIKO NL

Re: V.10 Interface on the TeKaDe FS-220(Z)

#10

Beitrag: # 18889Beitrag deBart »

:scratch: I've bought a keyboard from them, and a couple of manuals. The manuals were fine, the keyboard was nice to experiment with but would never had worked :mad:

YMMV, of course.
BartW. +++

35822 STIKO NL - FS220 + Fsg T56
42223 CMVZW NL - T100 mit Fsg 100 TL
T1000Z - Lauft (noch lange) nicht :coffee:
Antworten

Zurück zu „Service and Support“